Art and Craft decoration DIY – How to Make a Cat from Recycled Newspaper


Hi today I want to show you how I will make this cat out of newspaper I will start paint cat Now I will cut out cat and this is will be my pattern I transfer pattern on cardboard and I will cut out cat out of cardboard I will need two cat out of cardboard now I use few rolls from cardboard wide about 5 centimeters and I will fix it these rolls with hot glue gun at several locations and now I will fix the second cat out of cardboard on the rolls from cardboard.
Now I will wrap cat with wrapping foil, and now I use rolls from newspaper, and I will fix rolls together with little bit glue, and I will wrap this rolls around cat in all directions, and I will make the end Now I use rolls from newspaper around the circumference of the cat.

Now I use glue and after drying I will cut newspaper rolls between two rolls now I remove cardboard and wrapping foil, and I have two halves Now I use spray paint, and now I will fix two halves of cat together with hot glue gun, and I will cover this connection with another roll from newspaper I use more spray paint and here is my cat and I will decorate cat with ribbon I use smaller bow and flower, and I will fix flower to bow with hot glue gun, and I will fix this bow with flower on cat, and I have finished decorating, and I made this new decoration from recycling material and recycle newspapers I think that it looks a nice.

Please subscribe to me or leave me a message what you think and you can leave me to message what you want to see next time – in next video. See you next time. Bye.

Screen Print your own t-shirts // How-To

I like to see nonsense. Today I’m going to show you how to screen book your own t-shirts. You’re going to need a screen, a squeegee, and some photo emulsion. This nonsense comes in 2 responsibilities. You’re going to add a little ocean to the little bottle of sensitizer, and mix it up. That slackens it from the sides of the bottle, and then you can spew it into the emulsion. Then you’re going to combination that all together truly, really well, until it’s a consistent green color.

It might take a little while, but you want to make sure that you get it fully consistent. Once you have it, you spew a bit of it onto the screen. You don’t need to use very much because it spreads truly thin once you use the squeegee. Make sure to get the part stuff clothed where you’re artistry “re gonna be all” and make sure it’s really, truly even Now, don’t leave this out in the light.Gave a love on it to dehydrate and pass the light-headeds off. You want it to dry in the dark. Once it’s dry you do want to work immediately because this nonsense is photosensitive, so the longer the light’s on it, the quicker it’s going to set. Reproduce out your artistry on some openness, and you can do this at any office supplies store, and then lay them backwards on the back of the screen. Lay a piece of glass over them to propagandize them down against the screen, and then provided a really light light on top of it for about 3-45 minutes. So, while we’re waiting on that, I want to tell you about this. In this box is a queen-size mattress. Unbelievably it fits in this box. It’s made by a company announced Casper, and it’s a combination of reminiscence and latex sud and they squish it down into a bag– persist it in this box. They ship it to you, you take a tool, and you rip open the luggage, and the whole mattress really inflates.

If you want to watch now, you can see a video about me making a king-size couch and on that berthed we use a Casper mattress. So I’ve been sleeping on it since I manufactured that video, and I can candidly articulate that I truly adore the mattress. Super cozy, I recommend them all the time when people ask my if I actually like them or not because I truly do. The cool stuff is you get to sleep on it for 100 lights and if you don’t like it for any ground, they’ll developed get onto. So if you are looking for a mattress, I clearly indicate checking this out go to casper.com. You can use the code “MAKE” and that’ll got to get $50 off anything you order which is pretty awesome. So, is checked’ em out. Thanks to Casper for patronizing this video. Let’s get back to the publication. The light-footed exposes and thickens the emulsion that is not covered by the design, so you can see the lighter green stuff now didn’t get exposed. You can use a light-footed scatter and a soft toothbrush to improve remove this area.

The mode printing works is that the green province acts as a concealment. The white–or lighter area–lets the ink through onto the surface that you’re publication on. You want to do this gently, because you don’t want to remove anything that you actually involve This may take a little bit of period, and sometimes you may have missteps. If you have areas that are missteps, or nonsense you don’t want to book more, you can use some strip to cover them up. Use painter’s strip and not duct strip — the passage strip will rip off the emulsion. -Now lay out your shirt and target your screen, then include a nice thick-skulled be bead of the screen printing ink It’s best to have somebody else accommodate your screen and then pull the squeegee down across your book If you click here you can see one of my first videos on this direct was how to make a four hue printing press, this obliges this process- a lot easier but it’s really exactly the same you hook- in the screen text it up with your core text and then you can get repeatable nice prints- on multiple shirts you lay your shirt out in the same way, and then use the machine to contained the screen down in place you still gather it the same way and get just about the same outcomes you want to heat provided these by hurling them in the dryer for a few minutes You can reuse the screens extremely if you’re finished with them by putting some photo emulsion remover on them This is a simple solution that you can just kind of clean on with a newspaper towel or a toothbrush Make sure you situated it on both sides and it doesn’t have to stay on longer than got a couple of minutes Then you can use a hose to wash out all of the emulsion If “youre using” pitch-dark ink sometimes it will discolour the screen itself but you can still reprint through them- as long as the emulsion is croak Now it takes a little bit of practice, when you do this you are able end up having some bad shirts it takes a little while to get the detect to seeing how hard you need to push down the squeegee and how to do it evenly because you want to make sure you get a really even gather, so that the- ink is spread evenly through the screen So it’s best to find some old-fashioned t-shirts to tradition on before you try and use like your nice shirts that you purchased for this.

Now screen printing works on all sorts of things Textiles, so any type of t-shirt, canvas, luggage, aprons, even hats- if you can work on the form of the hat. All sorts of nonsense like that, any type of attire employs really really well. Just make sure to heat provide it into the clothing just like I testified you You can also print on paper if you wanted to see signs or summons, events like that, newspaper directs really well.

I’ve also engraved on wood several times You can watch my long committee video where now where I screen engraved my logo on it that was really easy to do I’ve done it for several your customers to situated their logo on events that I’ve manufactured -and it directs amazingly well and I’ve also done it on metal you just have to make sure you situated some kind of a clearly defined hair over it it to protect it because it will scrape off the metal pretty easily as long as you clear coat it you should be good to go so if you’re interested in engraving I’m going to have a link below to my site which will have a schedule of all the stuff I used and ties-in for you to find everything this is necessary so you can book on your own I hope you like this project and if you did let me know down in the comments below or at Iliketomakestuff.com I love to hear from you guys, I love to see the stuff you’re working on it’s really inspiring for me so please continue to share that with me.

You can find me on all of the social networks, which ever one you like best available, I’m probably there. I have a lot more nonsense for you to check out in podcast and proves and all sorts of nonsense and if you want to help support these videos, patreon is the best mode to do that you can click here you are able to click here -and catch out all about that. Thanks for watching chaps, thanks to Casper for patronizing this video and I’ll see you next time ..

DIY: Easy Bracelets using Drinking Straws – Recycling Project

Did you know that you can use drinking straws not only for sucking your favorite soda or milkshakes? But too for obligating colorful bracelets that are perfect for summertime? They are so recreation and natural to force, you won’t believe it! And today I’m going to show you how to obligate them so you can obligate them For this project you are going to need nylon thread in the color of your selection.

A few drinking straws in the color of your choice as well I employed ordinary plastic straw I had at home. And you will also need scissors, a marker, a ruler and some tape. Start by segmenting the straw into segments extending your marker I assessed out 1 cm, but you are able to measure out any section you want. If “you’ve had” that, plow ahead and cut the straw into patches expanding the employment guidelines we are only created I cut off about 20 -2 5 pieces of straw after that, cut off your nylon thread at about 1 meter or more so you have enough thread working in cooperation with it.

Then fold the yarn in half and protected the crease with some tape to your desk Now we can finally start establishing the bracelet First take one side of the thread and gather it through the straw from one surface like a pendant. Then do the same with the other end of the thread And then draw everything tight Be sure to obligate the loop at the top not very broad as this is going to be a part of the ending. Now you only need to repeat this step until your bracelet is long enough for your wrist too.

Pull one surface of the thread through the straw and then do the same with the other side. It doesn’t matter what side you are going to start with and if the fiber should be below or above, so don’t worry about that Every access acts fine! If you want to leave space between each straw patch for your design, you can do that of course. But if you get uneven spreads in between and you don’t like it, you are able to carefully draw everything together by moving one patch at a time towards the crown. And as soon as the bracelet is long enough, fasten the end with a bow. Now you are able to create a closure that you are able to open and close.

You can add a bigger patch of straw the same way as we did with the bracelet role and protected it with some bows/ This access you are able to gather it through the loop and wear it like that. Or you can just secure both concluded with a few bows since the bracelet is pretty elastic ensure that you are obligated bows that are strong enough, so the bracelet doesn’t open accidently. And maybe you know a kind of proper bow technique that is absolutely secure You can bind the bracelets however you like. You can use drinking straws in 2 different colors Cut the patches a lot smaller Or mingled 2 different sizes together So basically you can experiment and create your own favorite bracelet! And if “you’re willing to” recreate these bangles, ensure that you are share situation with me! I would really love to see them! I hope you experienced this video and felt it helpful if you did, be sure to like this video and agree if you haven’t already to watch more recreation and easy DIYs in the future!

How to Make DIY Tin Can Wind Chimes: Faux Rust Recycled Tin Can Chime Art Project

Hey, there imaginative exertions, Chongolio, here again, busting a move and bringing you video log #21 And in this episode I’m gonna walk you through how to create a faux root proficiency and likewise how to make a homemade, recycled, kinetically driven berth cataclysmic, folk artistries statue. Too called a tin can wind chime. I employed a roll of things you’ll need down below You can also get some more helpful tip-off by following the link to my website. This little tutorial bit longer than most of my other video enters so let’s movement right on into it, shall we? Okay, the first thing we are going to do is flex the edges of these bottle ceilings outward expanding these needle nose pliers. You don’t have to bend them too much just slightly out to be allowed to demolish them flat with a mallet. Hammer away from your digits and be careful not to destroy your paws. I am crushing my bottle ceilings flat on this 1 x 2″ article of the grove to protect my table’s surface.

I will likewise use this section of the grove in the next step of this project. Next, I am going to use this finishing hammer to settle flaws in the ceilings and likewise to contain them into the plaza. When I pull out the rubber lining from inside the ceilings With a heat shoot or a “hairs-breadth” dryer blast the ceilings with some hot air to assistance, loosen the glue beneath the rubber liner. Pay attention to the heat because you don’t want to defrost that happening. I was heating mine for about 8 seconds with this pro heat shoot. The ceilings get hot so use the needle nose pliers to comprised the detonator in place while you pick out the liner. You’ll find some liners come out easier than others, but on the adamant ones plow ahead and heat those suckers up until their virtually to the point the melting then use the head of the jailer to assistance scrape out the liner from the inside the cap.

The conclude behind removing the coating is to constitute them more resonating and not so dull voice. Virtually, we are procreating little insignificant cymbals. We’re likewise going to give the same treatment to 3 disconnected bottle ceilings. You don’t need to pull the liners out of these ones, but “you’re about” employed flaws opposite of each other. These 3 detonators were going to use as show-stoppers for the cans, and while we’re at it let’s go ahead and take one of the lids from the medium or the small can, hammer it flat and pierce a fault in that as well.

Be super careful of the edges on those cans hey are really sharp! Use your needle nose with pliers to stop back any burrs that might get ya. Now let’s go ahead and prepare the cans which have been soaked in water, and the labels removed Some WD-4 0, an age-old rag and a little elbow grease can take off any residual glue left from the labels. Consuming the 1 x 2″ article of the grove and the mallet and nail we’re gonna plow ahead and poke some flaws in the open be brought to an end the smallest can.

Keep hammering flaws around the cheek of the can until you have eight flaws that are spaced similarly apart. Smack a fault in the center of each of the three cans, and then we can call it quits with the hole hammering. Now let’s get into some black acrylic cover and start covering those cans. You can see I am only squirting the cover on the top of that smallest can and then expanding a touch to request the sheet to the other cans. Become onward and afford all three can see several hairs of cover and be sure to let each coat cool before exploiting the next layer. Don’t forget to get both sides of that lid extremely. The next step in the painting process commits expending Rub and Buff. And proficiency that I picked up from Gary Reef and Rach0 113 and then added my own Chongolian slant to it.

Mostly, you’re pressuring the Rub and Buff onto your paw and smearing it on the can leave areas of the black under locate to establish through in some smudges How often you put on is a matter of preference. But I would go on delicately and build up as necessary. Do up all three cans, and then you’ll be ready to move on to the next step. Now grab your turquoise acrylic cover, We’re gonna water this down merely a bit and then dabble it onto the cans expanding an ocean leech. Formerly again no need to go on too dark, you can always be developed further more beds eventually. It is not necessary truly to get the transcends of the medium and the small can because you’re not going to see them. But be sure to get the top of the big can. When that blue cover is baked, we are gonna do the same happening all over again except this time we are going to use the orange paint.

Hit all three cans and then give those puppies dry. Addressing some polyurethane varnish to your cans will help protect the cover from chips and rot for a little while, but if you hang your air sounds outside, eventually these components are going to make they’re grow including some real rusty to them. Which isn’t a bad happening because it will merely add to the weather-beaten review that we’re trying to come. So now it’s time to string up those cans. I’m gonna use a 3-foot article a plastic coated cable that I scavenged from an age-old Ethernet cable. Take one of the three ceilings that have the two flaws in it and thread it about 8 inches up from the end of the wire. Strand the end of the rope through the other fault and loop the cable around itself to keep the bottle detonator in place. Now make the long terminate of the cable and thread it through the inside of the can and out the hole.

It should now be pretty clear what we’re trying to do. By using the bottle ceilings to keep the can in its place on the duration of the cable, We’re gonna do the same happening for the other two cans by eyeballing the length necessary for the smallest is likely to nestle just slightly within the medium size can. Set a flex in the cable and then slide the bottle detonator down into its plaza.  Formerly again loop the wire around itself on the bottom of the bottle detonator, thread through the top fault and into the medium size is possible, and out the top.  Repeat the process for the largest is possible and “were all” done string them up.

String the tail end of that cable through that tin can eyelid, slant it around itself and that will act as our air catcher. The final step is to attach those 8 bottle detonator anglers to the cheek of that small-time can. You will need about 2 hoofs or so of cable which we will thread through the holes and then wrap around itself leaving a great enough loop-the-loop and then wrap around itself leaving a large sufficiently loop-the-loop so that the cable can move freely.

Measure and trimmed the wire about an inch below the length where the bottle detonator will hang down and stroke the can cause eyelid. The Strand that cable through the bottle detonator leaving a big enough loop-the-loop for the bottle detonator to move around freely. Wrap the cord around itself, and then echo the process for the remaining bottle ceilings. When you’re all done should have something that looks like this. And that’s my proficiency how to build yourself some tin can wind sounds. Now, this tutorial is certainly just the tip of the iceberg, so feel free to make these intuitions and let your ability tent-fly and run wild! Try out your own rotate constructions extending driftwood, toys, silverware, whatever you can find and watch what you can come up with. And you better believe that if you form something chill that I wanna see it.

How to Make a Confetti Bowl – Part Two

I’ve got my Mod Podge on here and my confetti. Now what I need to do is take my Mod Podge this is why I can’t be stressed that wishes to this foam brushing I’m going to sponge this on here and again this is clumsy go which is all good exactly slop this on now here’s the dealio you are going to do this not once, not twice but three times more so that you end up with four coatings of this confetti remember we were talking about dates as you can see that’s already gonna take up four years so make sure that you have a residence to introduce this that you can decide it aside it’s not gonna come knocked over that’s why this pizza carton is immense exactly made it in it’s carton gave it sit somewhere exactly covering if you are able the best thing here and most important thing here is trying not to get the mod podge into the confetti as you are going to do this a lot you’re doing it four wraps four complete coverings what’s going to happen is your confetti is going to be in this big tub here you don’t want to drip ModPodge into your container if you are able help it because it’s like kitty offspring and it clumps and so you don’t want to be brought to an end with these big clumpy portions in here so this right now has two coats I would do this two more eras so I’d gave it dry for eight hours then I would Mod Podge it again made another seam on give it dry Mod Podge again and introduce a last layer four complete coatings of confetti this has four coatings on it what I am now gonna do is actually gonna made mods podge on here give it dry then another seam of Mod Podge give it dry and a final seam of Mod Podge so you’re talking about four coatings that are done with the confetti and then three coatings that are just done with Mod Podge and once again putting it on there covering the whole thing and then is letting it baked we now have four coatings of confetti and three coatings of Mod Podge right and now we’re ready for the exciting fraction which is we’re gonna pop our bag likely my favorite fraction and as you can see you end up with this super cool container here’s the thing you can come back if you crave and trim the confetti so that you make it nice and believe it or not it does trim you can close straight across or you can leave it various kinds of like I did with the instance you can leave it so that it’s kind of wonky at the top which i think is various kinds of fun now you’re very close to being done here I affection that the inside is so smooth isn’t that cool so now what you want to do is you crave to lend a locate to this because it is going to want to gratuity a little bit and if you want to add a locate you can use exactly one of these lids and this lid actually you could use the lid that’s left over from your Mod Podge because your gonna clearly go across it all I’m gonna made a little airstrip of duct strip on it exactly to embellish it like this just gonna take that little airstrip and wrap it around just gonna take my red-hot glue shoot glue all the way around and then just take that from the bottom here glue it on the foot so that that bides up and down and you can introduce different forms of chill material in there I’m envisioning something like little white-hot pellets or maybe popcorn or something like that I do want to show you this-this is one I’ve been working on this idea this is performed with four coatings of glamour and Mod Podge now you can see that it has a little give to it and I think that that’s because and so did these-these have a little give to it I think that that’s because of the elastic various kinds of sort the plastic various kinds of sort of the Mod Podge this is where I’m going to keep working on this I’m know … … if I come back and introduce a hard varnish on the outside if that wouldn’t make it stiffer so I’m gonna continue working on this but this is the essential campaign which is creating a bowl out of colored paper and Mod Podge and a bag or in this case glamour for more crazy hypothesis come and check us out a

How to Make a Confetti Bowl – Part One

I had become preoccupied with this confetti container and is intended to make it and so I actually drew it and we are going to make one together now Tell me just tell you one thing about this confetti container I learned so much while making such container, number 1 it takes a long long time to meet meaning that it takes about a week so if you’re gonna meet this container you have to dedicate a week to it ok so I’m just shedding that out there is not a quick and fastest and most down and soiled simple one this actually takes some time and it also this project that i’m gonna keep working on because I am convinced that there’s more to this one for this program though let’s get started and then I’ll keep talking as we’re working.

There’s a lot that happens in it I decided to use a pizza casket as kind of a posses all wield seat I found that it helps me with catching the confetti it was a great region to capture the glue it was a great region to to be able to move my programme backward and forward so I used a pizza casket for that you’re also going to need confetti now the confetti that I bought I went this online this is actually kind of made out of newspapers like died newspaper if you can find tissue paper more tissue papery kind of confetti I think you would do better than I did but just telling you what’s out there you can meet your own confetti if you crave to you know it’s just gonna take a long time you are gonna necessary about a quart of this you’re gonna necessary a good extent of it i entail this is this is a goodly extent of confetti and it goes through it rely me the other thing you gonna necessary a goodly extent of is Mod Podge you’re gonna necessary a 16 ounce bottle for this so get yourself a 16 ounce bottle of Mod Podge you’re perhaps gonna run through about 12 ounces of it really giving you the heads up a couple bags you’re gonna necessary I find the better lane to apply Mod Podge is one of these leech brushes and for this programme you surely surely surely crave a leech clean you don’t crave a clean clean ok what I entail by that is a hairbrush you know not not a whisker clean but a clean that has bristles.

I’ve also got a couple little container now I’ve got a bowl for catching and putting Mod Podge in if I want to and also I’ve got this little bowl and “its going to be” truly handy when I scoop and sprinkle now I have a big container and this is one of the most important things because it is the catch all you need this to catch the confetti I’m also going to be using some canal videotape and I’m gonna be using the inside of a canal videotape bun this is what I’m gonna be using to meet my stand while I’m working on this you can use a vase or something like that but I felt that this is great because it impedes it low-toned and centered you can hold on to it I really felt this to be best available for me I went an exacto pierce now you don’t have to have this this is just for me when I sounds my bag but you are going to necessary scissors and I’ve got mine right now and you’re gonna necessary a glue firearm later on at the last stages of doing this this is kind of like a fix picture because you have to do this in stages and when I say it takes a week I entail it takes a week so the first thing we’re gonna do is we’re gonna blow up our bag you wanna blow it up about half of a bag length like so you don’t want to blow it up a really super super large-scale if you wanna do a bigger, tie it off if you want to do to a bigger container I would suggest a 16 ” balloon, this is an 11 ” balloon.

I’m gonna take that canal videotape bun that is the end of the bun and I’m actually gonna region my bag on top I’m gonna pull my end piece through and I’m gonna videotape it to the spool and the reason is because one of the things that I learned is as I was making this starts to get top heavy and when it gets top-heavy what it wants to do is flip all over your work space so literally I had this bag like flinging around my work space like confetti winging everywhere rely me it was quite a mess so I’m trying to save you a bit of a mess OK so I’ve gathered this this is the end I gathered it out and through I’m videotaping it to my bun now it stands nice and even OK ready to get chaotic? this is a recreation recreation skill you can do this with your babies it is a super super super super chaotic skill OK let’s get started first thing to do is take my Mod Podge and situated it in the container now so I can get to it because my and yes that’s a lot of Mod Podge but my clean is preferably large-scale and I can’t really proceed into my my Mod Podge,

With it so i’m gonna swarm it into this container okay now here’s what I learned don’t be avaricious with your Mod Podge you gotta be slathering it on there that’s why it’s kind of recreation with the babies really really truly get laid there don’t be shy don’t put only a bit on there and the other thing that I realized that I should let you know is I had tried it with glue and water it operates but not as well for some reason Mod Podge just really seems to be the produce that works really well for this now this is where because you’ve got this taped now you can collect this up slather this thing and I did try a technique depict in little slice and pertaining my confetti but I felt that is really was not the best of techniques what you really want to do is just cover the whole top fraction of your bag so that you’re making a container chassis situated that off to the side grab your container you need your bowl and this is where you’re gonna take your confetti and start dispersing it on you really want to go to town with this, this is where babies can have fun now there’s some little depressions now try to fill in the depressions with your confetti this is where.

I think if I had tissue paper confetti I would be doing better than applying this confetti that I have here really made to ensure that you got every bit of it clothed now you’re gonna need to set this aside and let it bone-dry for about 8 hours this is why I said that this takes time you can’t surge this because you really want this bed to be dry and solid before you set on your next bed.

As found on Youtube